Operator´s manualFloor sawBFS 1350AL0201438en 00501.2011
3 Safety10MalfunctionsIf you detect a malfunction, you must shut down and secure the machine immediately.Eliminate the malfunctions that impair safety
3 Safety11Operator's controlsAlways keep the operator's controls of the machine dry, clean and free of oil or grease.Operating elements such
3 Safety12Work recommendationsPlease observe the recommendations below: Work only if you are in a good physical condition. Work attentively, particu
3 Safety13Breathing protectionIf a lot of dust is produced when cutting, always wear suitable breathing protection.Use the water supply.Provision of f
3 Safety14LiftingWhen lifting the machine, observe the following instructions: Designate a skilled person to guide you for the lifting procedure. Yo
3 Safety153.5 Operating safetyExplosible environmentNever operate the machine in a potentially explosive environment. Work environmentFamiliarize your
3 Safety16Vertical stabilityAlways ensure that the machine is vertically stable and cannot tip over, roll or slide away. Proper operator positionDo no
3 Safety17StorageStore the machine securely so that it cannot tilt, fall or slip. Storage locationAfter operation, allow the machine to cool and then
3 Safety18Preventing firesOpen flames and smoking are strictly prohibited in the immediate vicinity of the machine.Make sure that waste, such as paper
3 Safety19Cleaning the engineClean the engine when it is cool to remove any dirt.Do not use gasoline or solvents. Danger of explosion! Health hazard
ManufacturerWacker Neuson SEPreußenstraße 4180809 Münchenwww.wackerneuson.com Tel.: +49-(0)89-354 02-0Fax: +49-(0)89-354 02-390Translation of the orig
3 Safety20Wet-cuttingUse a water sprayer when dust formation is excessive, e.g. when cutting concrete or stone.Only use cutting blades that are suitab
3 Safety21Do not touch a rotating cutting bladeNever touch a rotating cutting blade with your hand or any other body part. Danger of severe injury. Pa
3 Safety22 3.8 MaintenanceMaintenance workService and maintenance work must only be carried out to the extent described in these operating instruction
3 Safety23Handling operating fluids safelyObserve the following points when handling operating fluids, e.g. fuels, oils, greases, coolants etc.: Alwa
3 Safety243.9 Safety devices Cutting blade guardNever operate the machine without a cutting blade guard.The cutting blade guard performs the followi
4 Safety and information labels254 Safety and information labelsYour machine has adhesive labels containing the most important instructions and safety
4 Safety and information labels262Item Label Description1 Caution, risk of injury Read the operator's manual. Wear a eye protection and ear p
TD00673GB.fm 271. Technical dataBFS 1350AL BFS 1350LBFS 1350ALSItem no.00088980610398000893600088850610399Length x Width x Height mm (in): 1085 x 604
TD00673GB.fm 28Spark plug Type:NGK BPR6ES / Denso W20EPR-UNGK BP6ES / Champion N9YNGK BPR6ES / Denso W20EPR-U(*) In accordance with the installed usef
DescriptionT01134GB.fm 291. Description1.1 Application∗ Cutting expansion joints in concrete and asphalt surfaces.∗ Repair work on streets, e.g. cutti
Table Of Contents31. Technical data 272. Description 292.1 Application ...
DescriptionT01134GB.fm 30 1.3 Functional descriptionThe floor saw must only be operated in a forward direction (see arrow).The drive motor (2) attache
DescriptionT01134GB.fm 31The revs on the engine can be infinitely varied using the throttle controllever (4); the optimum cutting speed of the blade i
Transport to the worksiteT01135GB.fm 322. Transport to the worksiteRequirements:∗ When transporting the floor saw, use only suitable hoisting gear wit
OperationT01136GB.fm 333. Operation3.1 Adjusting the handleThe width and height of the handles can be adjusted according to theuse and the body height
OperationT01136GB.fm 343.2.2 Aligning the guide wheelTo do this, make a cut of approx. 2 m length on a flat surface and withthe minimum cutting depth.
OperationT01136GB.fm 353.3.2 To set the scale proceed as follows: 1. Push quick-lift lever (3) fully forwards.2. Turn the cutting depth crank (5) unti
OperationT01136GB.fm 36 The adjustable hose coupling (19) can be used as a feeder point (1/2-inch) for an external hose connection.3.5 Parking brakeTo
OperationT01136GB.fm 373.6 Assembling the cutting blade3.6.1 Checking a new cutting blade: ∗ The blade type must be suitable for the material to be cu
OperationT01136GB.fm 383. Place an intermediate layer (disc label) under each faceplate whenusing bakelite-bonded cutting discs.4. Attach cutting blad
OperationT01136GB.fm 394. Disconnect the water hose.5. Fold up the cutting blade guard (1).6. Loosen the tightening nut. Hold cutting shaft with spann
1 Foreword41ForewordThis operator's manual contains information and procedures for the safe opera-tion and maintenance of your Wacker Neuson mach
OperationT01136GB.fm 40Note: Carry out the following additional conversions if needed:∗ Loosen screws (27), turn guide wheel around and then reassembl
OperationT01136GB.fm 413.10 Starting the engineThe cutting blade must not be in contact with the ground.1. Open the fuel tap..2. Move the choke lever
OperationT01136GB.fm 425. Pull starter handle out slowly until a slight resistance is felt, then pullhandle with strength. Caution: Do not allow the s
OperationT01136GB.fm 43 3.11 Operation the engineAs the engine warms up, gradually move the choke lever to the OPENposition. Set required engine speed
OperationT01136GB.fm 443.12 Switch off the engineTo turn off the engine in the event of an emergency, switch the mainswitch (1) to "0". Unde
MaintenanceT01137GB.fm 454. Maintenance4.1 Maintenance scheduleComponent Maintenance workMaintenanceintervalMachineCheck for signs of damage and wear
MaintenanceT01137GB.fm 464.2 Checking engine oil level∗ Turn off the engine.∗ Align the engine bolting level horizontally.∗ Remove any dirt around the
MaintenanceT01137GB.fm 474.4 Cleaning the air cleanerA dirty air cleaner obstructs the flow of air to the carburetor. To preventcarburetor malfunction
MaintenanceT01137GB.fm 484.5 Cleaning the filter cupClose the fuel tap. Remove the filter cup with the o-ring and wash it outwith non-combustible and
MaintenanceT01137GB.fm 494.7 Tightening the beltCheck the belt in the course of the weekly engine maintenance andretighten it as follows, if necessary
2 Introduction52 Introduction2.1 Means of representation for this operator's manualWarning symbolsThis operator's manual contains safety inf
MaintenanceT01137GB.fm 504.8 Changing the belt1. Disassemble V-belt guard (above and below) and cutting disc guard.2. Take tension off V-belts. To do
MaintenanceT01137GB.fm 514.9 Checking the spark plug ∗ Remove any soot deposits from the electrodes of the spark plug using aspark plug cleaner or a w
5 Troubleshooting525 TroubleshootingPotential faults, their causes and remedies can be found in the following table.Notify your Wacker Neuson represen
6 Emission control systems information and warranty53 Operator´s manual6 Emission control systems information and warrantyThe Emission Control Warrant
7 Glossary547 Glossary7.1 Use of oxygenated fuelsSome conventional gasolines are blended with alcohol. These gasolines are col-lectively referred to a
www.wackerneuson.comEC Declaration of ConformityManufacturerWacker Neuson SE, Preußenstraße 41, 80809 MünchenProductConformity assessment procedure ac
2 Introduction6Instructionsf This symbol indicates there is something for you to do.1. Numbered instructions indicate that you have to carry out some
2 Introduction72.4 Identification of the machineNameplate dataThe nameplate lists information that uniquely identifies your machine. This infor-mation
3 Safety83Safety3.1 PrincipleState of the artThis machine has been constructed with state-of-the-art technology according to the recognized rules of s
3 Safety9Structural modificationsNever attempt to modify the machine without the written permission of the manufacturer. To do so will endanger your s
Commentaires sur ces manuels