Wacker Neuson BPU 3050A Manuel de l'opérateur

www.wackergroup.comOperator's manualVibrating plateBPU ...0210447en 00107.2006

Safety informationSV00069en.fm 102.4 Maintenance2.4.1 Only use original spare parts. Alterations to this machine, incl.adjustments of the maximum engi

Safety informationSV00069en.fm 112.5 Transport2.5.1 For the loading and transportation of compacting machines withhoisting gear, suitable sling chains

Technical dataTD00732en.fm 123. Technical dataBPU 2540 BPU 3050Item no.0008954 0008955Length x Width X Heightmm:733 x 400 x 1170 733 x 500 x 1170Opera

Technical dataTD00732en.fm 13(*) corresponds to the installed effective power in accordance withDirective 2000/14/EC.Spark plug air gap mm:0.6 - 0.7En

DescriptionT01090en.fm 144. Description4.1 Field of application4.1.1 BPU 2540Through the low width and continuous switchability especially suitablefor

DescriptionT01090en.fm 154.3 Functional descriptionThe vibration required for compaction is generated by the exciter (5)that is permanently attached t

DescriptionT01090en.fm 16The upper mass (3) and the base plate (4) are connected to each othervia 4 vibration-damping rubber metal shockmounts (11). T

Transport to the worksiteT01091en.fm 175. Transport to the worksiteRequirements:∗ When transporting the vibrating plate compactor, use only suitableho

Recommendations for compactingT01091en.fm 186. Recommendations for compacting6.0.1 Condition of the groundThe maximum layer thickness depends on sever

OperationT01092en.fm 197. Operation7.1 Start preparationBefore you start the engine, check the following:f Fuel level – the tank should be at least ha

OperationT01092en.fm 207.3 Operating in the forward and reverse directionf Press the control handle in the direction of travel.Note: The forward and r

MaintenanceT01093en.fm 218. Maintenance8.1 Maintenance schedule TaskDaily before operationAfter the first 20 hoursMonthly or every 100 hoursAnnually

MaintenanceT01093en.fm 228.2 Checking engine oil levelf Place the machine upright on a flat surface.f Remove any dirt around the oil level dipstick.f

MaintenanceT01093en.fm 238.3 Changing the engine oilNote: The work area should be covered with a waterproof sheet to protect the floor (protection of

MaintenanceT01093en.fm 248.4 Cleaning the air filter / replacing the air filter insertsThe air filter is equipped with two air filter inserts. Note:

MaintenanceT01093en.fm 258.5 Checking / cleaning / replacing the spark plug f Remove the spark plug connector.f Remove the spark plug with a spark pl

MaintenanceT01093en.fm 268.6 Checking exciter V-belt f Remove V-belt protector.f Check exciter V-belt for signs of damage. Replace damaged exciter V-b

MaintenanceT01093en.fm 278.9 Checking exciter oil levelf Place the machine upright on a flat surface.f Remove any dirt around the filler hole.f Open f

MalfunctionT01094en.fm 289. Malfunction9.1 Forward travel speed too low9.2 Reverse travel speed too low9.3 No forward movement9.4 Loss of hydraulic oi

MalfunctionT01094en.fm 299.5 Engine will not startCause RemedyFuel tank empty. Refill with fuel.Fuel tap closed. Open.Air filter dirty. Clean.Engine s

Contents31. Foreword 52. Safety information 72.1 General instructions ...7

MalfunctionT01094en.fm 30

C0036007en.fmPlease keep this document in a safe placeEC Declaration of ConformityWacker Construction Equipment AG, Preußenstraße 41, 80809 Münchencer

DIN EN ISO 9001 CERTIFICATE

Wacker Construction Equipment AG - Preußenstraße 41 - 80809 München - Tel.: +49-(0)89-3 54 02-0 -

Contents49.5 Engine will not start ...29EC Declaration of Conformity 31DIN

Foreword51. ForewordFor your own safety and protection from bodily injuries, carefully read,understand and follow the safety information in this manua

T00940en.fm 6Important noteThis machine is equipped with an EPA-certified motor.Relevant details can be found in the instructions of the motormanufact

Safety informationSV00069en.fm 72. Safety informationFor vibrating plates with combustion engine drive2.1 General instructions2.1.1 Vibrating plates m

Safety informationSV00069en.fm 82.2.3 The operator must not leave the operator's area during the operationof the machine. 2.2.4 Before going on b

Safety informationSV00069en.fm 92.2.13 Wear suitable protective clothing during work and maintenance work. 2.2.14 When operating in the reverse direct